rdx et disque dur externe

[emmesse]

Bonjour,

la cartouche, ou le lecteur, rdx déconne lors que je branche le rdx et le disque dur en même temps. Le rdx est impossible à démonter (et éjecter)
sur mon autre ordinateur, ça fonctionne très bien.
Quelqu’un saurait-il me donner une explication?

[piratebab]

Désolé, mais avec si peu d'info, difficile de répondre.
Essaie de faire un dmesg aprés avoir branché tes appareils (les derniéres lignes indiquent comment est reconnu l'appreil)

[emmesse]

[11241.752961] pcieport 0000:00:1c.3: AER: Corrected error message received from 0000:02:00.0
[11241.753086] ath10k_pci 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Data Link Layer, (Receiver ID)
[11241.753090] ath10k_pci 0000:02:00.0: device [168c:0042] error status/mask=00000080/00006000
[11241.753094] ath10k_pci 0000:02:00.0: [ 7] BadDLLP
[12769.755208] usb 2-1.1.4: new SuperSpeed USB device number 5 using xhci_hcd
[12769.776966] usb 2-1.1.4: New USB device found, idVendor=1a5a, idProduct=0006, bcdDevice= 2.27
[12769.776975] usb 2-1.1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[12769.776978] usb 2-1.1.4: Product: RDX
[12769.776980] usb 2-1.1.4: Manufacturer: TANDBERG
[12769.776982] usb 2-1.1.4: SerialNumber: 008640756372
[12769.778690] usb-storage 2-1.1.4:1.0: USB Mass Storage device detected
[12769.778851] scsi host3: usb-storage 2-1.1.4:1.0
[12770.780272] scsi 3:0:0:0: Direct-Access TANDBERG RDX 0227 PQ: 0 ANSI: 6
[12770.780519] sd 3:0:0:0: Attached scsi generic sg1 type 0
[12770.781160] sd 3:0:0:0: Power-on or device reset occurred
[12770.781795] sd 3:0:0:0: [sdb] Media removed, stopped polling
[12770.782260] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[13166.010584] sd 3:0:0:0: [sdb] 1953516976 512-byte logical blocks: (1.00 TB/932 GiB)
[13166.011449] sdb: detected capacity change from 0 to 1953516976
[13166.040256] sdb: sdb1
[13166.537170] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Quota mode: none.
mathieu@portable:~ 05:35:21 $ df
Sys. de fichiers blocs de 1K Utilisé Disponible Uti% Monté sur
udev 3870760 0 3870760 0% /dev
tmpfs 780824 1944 778880 1% /run
/dev/nvme0n1p2 47745772 8053892 37234076 18% /
tmpfs 3904116 0 3904116 0% /dev/shm
tmpfs 5120 8 5112 1% /run/lock
/dev/nvme0n1p3 143075484 32250992 103483852 24% /home
/dev/nvme0n1p1 523248 12180 511068 3% /boot/efi
tmpfs 780820 104 780716 1% /run/user/1000
/dev/sda1 960310988 33356132 878100432 4% /media/mathieu/Expansion
/dev/sdb1 960306892 31987484 879465188 4% /media/mathieu/rdx1To
Expansion est le disque dur et rdx1To est le rdx

[PascalHambourg]

Et quels sont les messages lors du branchement du lecteur quand le disque dur n'est pas connecté ? (pratique : exécuter "dmesg -W" puis brancher le périphérique pour afficher les nouveaux messages seulement)
Comment tout cela est alimenté ?

[emmesse]

Code : Tout sélectionner

[  297.696808] usb 2-1.1.2: new SuperSpeed USB device number 6 using xhci_hcd
[  297.718856] usb 2-1.1.2: New USB device found, idVendor=1a5a, idProduct=0006, bcdDevice= 2.27
[  297.718866] usb 2-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  297.718869] usb 2-1.1.2: Product: RDX             
[  297.718872] usb 2-1.1.2: Manufacturer: TANDBERG
[  297.718874] usb 2-1.1.2: SerialNumber: 008640756372
[  297.720630] usb-storage 2-1.1.2:1.0: USB Mass Storage device detected
[  297.720874] scsi host3: usb-storage 2-1.1.2:1.0
[  298.741492] scsi 3:0:0:0: Direct-Access     TANDBERG RDX              0227 PQ: 0 ANSI: 6
[  298.741883] sd 3:0:0:0: Attached scsi generic sg1 type 0
[  298.742488] sd 3:0:0:0: Power-on or device reset occurred
[  298.742960] sd 3:0:0:0: [sdb] Media removed, stopped polling
[  298.743343] sd 3:0:0:0: [sdb] Attached SCSI removable disk
[  306.863989] sd 3:0:0:0: [sdb] 1953516976 512-byte logical blocks: (1.00 TB/932 GiB)
[  306.864938] sdb: detected capacity change from 0 to 1953516976
[  306.894251]  sdb: sdb1
[  320.564666] sd 2:0:0:0: [sda] tag#20 uas_eh_abort_handler 0 uas-tag 2 inflight: CMD 
[  320.564673] sd 2:0:0:0: [sda] tag#20 CDB: Synchronize Cache(10) 35 00 00 00 00 00 00 00 00 00
[  320.588653] scsi host2: uas_eh_device_reset_handler start
[  320.673040] usb 2-1.1.1: reset SuperSpeed USB device number 4 using xhci_hcd
[  320.695771] scsi host2: uas_eh_device_reset_handler success
[  382.008770] scsi host2: uas_eh_device_reset_handler start
[  382.009018] sd 2:0:0:0: [sda] tag#7 uas_zap_pending 0 uas-tag 1 inflight: CMD 
[  382.009023] sd 2:0:0:0: [sda] tag#7 CDB: Synchronize Cache(10) 35 00 00 00 00 00 00 00 00 00
[  382.009027] sd 2:0:0:0: [sda] tag#4 uas_zap_pending 0 uas-tag 2 inflight: CMD 
[  382.009030] sd 2:0:0:0: [sda] tag#4 CDB: Read(10) 28 00 00 00 08 02 00 00 02 00
[  382.297114] usb 2-1.1.1: reset SuperSpeed USB device number 4 using xhci_hcd
[  382.317282] usb 2-1.1.1: device firmware changed
[  382.317618] scsi host2: uas_eh_device_reset_handler FAILED err -19
[  382.317624] sd 2:0:0:0: Device offlined - not ready after error recovery
[  382.317627] sd 2:0:0:0: Device offlined - not ready after error recovery
[  382.318044] usb 2-1.1.1: USB disconnect, device number 4
[  382.332750] blk_print_req_error: 17 callbacks suppressed
[  382.332756] device offline error, dev sda, sector 2050 op 0x0:(READ) flags 0x1000 phys_seg 1 prio class 2
[  382.332779] device offline error, dev sda, sector 0 op 0x1:(WRITE) flags 0x800 phys_seg 0 prio class 2
[  382.332794] EXT4-fs (sda1): unable to read superblock
[  382.332875] device offline error, dev sda, sector 2048 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[  382.332913] device offline error, dev sda, sector 2048 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[  382.332918] buffer_io_error: 23 callbacks suppressed
[  382.332919] Buffer I/O error on dev sda1, logical block 0, async page read
[  382.332929] device offline error, dev sda, sector 2050 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[  382.332933] Buffer I/O error on dev sda1, logical block 1, async page read
[  382.332944] device offline error, dev sda, sector 2052 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[  382.332948] Buffer I/O error on dev sda1, logical block 2, async page read
[  382.332960] device offline error, dev sda, sector 2054 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[  382.332964] Buffer I/O error on dev sda1, logical block 3, async page read
[  382.332981] device offline error, dev sda, sector 2048 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[  382.332984] Buffer I/O error on dev sda1, logical block 0, async page read
[  382.332990] device offline error, dev sda, sector 2050 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[  382.332993] Buffer I/O error on dev sda1, logical block 1, async page read
[  382.333001] device offline error, dev sda, sector 2052 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[  382.333005] Buffer I/O error on dev sda1, logical block 2, async page read
[  382.333011] Buffer I/O error on dev sda1, logical block 3, async page read
[  382.360774] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[  382.577031] EXT4-fs (sdb1): recovery complete
[  382.577566] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Quota mode: none.
[  382.604831] sd 2:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[  382.960816] usb 2-1.1.1: new SuperSpeed USB device number 7 using xhci_hcd
[  382.981416] usb 2-1.1.1: New USB device found, idVendor=0bc2, idProduct=2030, bcdDevice= 1.00
[  382.981424] usb 2-1.1.1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  382.981427] usb 2-1.1.1: Product: Expansion HDD
[  382.981429] usb 2-1.1.1: Manufacturer: Seagate
[  382.981431] usb 2-1.1.1: SerialNumber: 0000000054FB2467
[  382.986419] scsi host2: uas
[  382.987044] scsi 2:0:0:0: Direct-Access     Seagate  Expansion HDD    0001 PQ: 0 ANSI: 6
[  382.988659] sd 2:0:0:0: Attached scsi generic sg0 type 0
[  382.989737] sd 2:0:0:0: [sda] Spinning up disk...
[  384.020742] ..................................................................................................not responding...
[  490.379007] sd 2:0:0:0: [sda] 1953525167 512-byte logical blocks: (1.00 TB/932 GiB)
[  490.379011] sd 2:0:0:0: [sda] 4096-byte physical blocks
[  511.228443] sd 2:0:0:0: [sda] Test WP failed, assume Write Enabled
[  518.178308] sd 2:0:0:0: [sda] Asking for cache data failed
[  518.178320] sd 2:0:0:0: [sda] Assuming drive cache: write through
[  518.178529] sd 2:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[  518.178534] sd 2:0:0:0: [sda] Optimal transfer size 33553920 bytes not a multiple of preferred minimum block size (4096 bytes)
[  518.179155] sd 2:0:0:0: [sda] Spinning up disk...

Code : Tout sélectionner

$ df
Sys. de fichiers blocs de 1K  Utilisé Disponible Uti% Monté sur
udev                 3870388        0    3870388   0% /dev
tmpfs                 780824     1956     778868   1% /run
/dev/nvme0n1p2      47745772  8181428   37106540  19% /
tmpfs                3904112        0    3904112   0% /dev/shm
tmpfs                   5120        8       5112   1% /run/lock
/dev/nvme0n1p3     143075484 32237552  103497292  24% /home
/dev/nvme0n1p1        523248    12180     511068   3% /boot/efi
tmpfs                 780820       44     780776   1% /run/user/0
tmpfs                 780820       92     780728   1% /run/user/1000
/dev/sdb1          960306892 31987484  879465188   4% /media/mathieu/rdx1To

Code : Tout sélectionner

$ ls /dev/sd*
/dev/sda  /dev/sdb  /dev/sdb1

les partitions du disque dur sda ont disparues, puis ont ré-apparuent en débranchant le rdx
sinon, pourquoi je ne reçois pas d'emails quand on me répond dans cette discussion?

[emmesse]

Pour les notifications par email, je crois que j'ai trouvé (c'est dans les options lorsque l'on rédige une réponse)

[PascalHambourg]

J'avais demandé "quand le disque dur n'est pas connecté", ce qui n'est manifestement pas le cas.
Et tu n'as pas répondu à ma question concernant l'alimentation.

[emmesse]

Code : Tout sélectionner

[  313.856626] usb 2-1.2: new SuperSpeed USB device number 5 using xhci_hcd
[  313.878467] usb 2-1.2: New USB device found, idVendor=1a5a, idProduct=0006, bcdDevice= 2.27
[  313.878476] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  313.878480] usb 2-1.2: Product: RDX             
[  313.878482] usb 2-1.2: Manufacturer: TANDBERG
[  313.878484] usb 2-1.2: SerialNumber: 008640756372
[  313.881795] usb-storage 2-1.2:1.0: USB Mass Storage device detected
[  313.881950] scsi host2: usb-storage 2-1.2:1.0
[  314.897177] scsi 2:0:0:0: Direct-Access     TANDBERG RDX              0227 PQ: 0 ANSI: 6
[  314.897466] sd 2:0:0:0: Attached scsi generic sg0 type 0
[  314.897979] sd 2:0:0:0: Power-on or device reset occurred
[  314.898462] sd 2:0:0:0: [sda] Media removed, stopped polling
[  314.898830] sd 2:0:0:0: [sda] Attached SCSI removable disk
[  323.006527] sd 2:0:0:0: [sda] 1953516976 512-byte logical blocks: (1.00 TB/932 GiB)
[  323.007307] sda: detected capacity change from 0 to 1953516976
[  323.036350]  sda: sda1
[  323.578046] EXT4-fs (sda1): recovery complete
[  323.578053] EXT4-fs (sda1): mounted filesystem with ordered data mode. Quota mode: none.

Code : Tout sélectionner

$ df
Sys. de fichiers blocs de 1K  Utilisé Disponible Uti% Monté sur
udev                 3870388        0    3870388   0% /dev
tmpfs                 780824     1920     778904   1% /run
/dev/nvme0n1p2      47745772  8189664   37098304  19% /
tmpfs                3904116        0    3904116   0% /dev/shm
tmpfs                   5120        8       5112   1% /run/lock
/dev/nvme0n1p3     143075484 32256132  103478712  24% /home
/dev/nvme0n1p1        523248    12180     511068   3% /boot/efi
tmpfs                 780820      100     780720   1% /run/user/1000
/dev/sda1          960306892 31987484  879465188   4% /media/mathieu/rdx1To

il n'y a pas d'alimentation, on le branche sur le hub usb avec deux prises usb

[emmesse]

Merci à ceux qui ont participé à cette discussion.
J'ai remplacé cet ordinateur et cela fonctionne avec celui-ci. Le sujet est maintenant obsolète.